Yagi Antenna Design

Yagi Front-to-Back Ratio: What It Means and How to Improve It

What Yagi front-to-back ratio means in dB, why it matters for rejecting interference, typical values, and practical ways to improve it without wrecking gain.

On this page
  1. What front-to-back ratio means
  2. Why it matters
  3. Typical values
  4. Front-to-back vs front-to-rear
  5. How to improve it
  6. The trade-offs
  7. Measuring it
  8. Real-world factors

What front-to-back ratio means

Front-to-back ratio (F/B) compares how strongly a directional antenna receives or radiates in its forward direction with how strongly it does so directly behind it. It is expressed in decibels (dB). If the forward gain is 10 dBi and the gain directly behind is -10 dBi, the front-to-back ratio is 20 dB.

A higher figure means more of the signal from behind is rejected. Each 10 dB is a tenfold difference in power, and 20 dB is a hundredfold difference.

Why it matters

  • Interference from behind. If a strong transmitter is behind your antenna, such as a second TV tower or a nearby radio station, a good F/B ratio helps reduce it.
  • Ghosting and multipath on TV. Reflections from buildings behind the antenna can cause picture problems. A better F/B ratio can help, though reflections that arrive from the front or sides are not helped.
  • Noise. On amateur bands, local noise sources behind the antenna are weakened.
  • Transmitting. Less energy radiated backward can be useful if you want to avoid causing interference to neighbors or other services behind you.

F/B does not change how well the antenna receives the signal you want. It only affects what comes from the back.

Typical values

The numbers vary by design, and published figures are often idealized, so treat these as rough ranges:

  • A simple three-element Yagi often has an F/B ratio somewhere in the teens of dB, sometimes up to the 20s.
  • Designs tuned for good rear rejection can reach 25 dB or more, at least at certain frequencies.
  • Broadband TV Yagis tend to have lower or less consistent F/B, because the design has to work across many channels.

Check how a manufacturer specifies the number, and whether it applies to one frequency or the whole band.

Front-to-back vs front-to-rear

Some specifications quote the front-to-back ratio, measured at exactly 180 degrees behind the antenna. Others quote the front-to-rear ratio, based on the strongest signal anywhere in the rear half of the pattern. The front-to-rear figure is generally lower, and more honest about how the antenna behaves, because the rear pattern often has small lobes at angles off directly behind. An antenna with a deep null straight back may still pick up signals from 140 or 150 degrees. When comparing antennas, make sure you are comparing the same measure.

How to improve it

The following apply to the antenna itself. Check them with a model or measurements, since changing one thing affects others.

  • Adjust the reflector. Its length and spacing from the driven element have a big effect on rear response. Small changes can deepen the null.
  • Use more than one reflector element, or a reflector made of a screen or grid of rods or wires, which can improve rear rejection and, with a good design, widen the effective response.
  • Optimize the director spacing and length. The director section interacts with the rear pattern, though to a lesser degree.
  • Use a model. A program such as 4nec2 or MMANA-GAL can show the full pattern and let you tune for F/B instead of guessing. The Yagi design workflow describes the overall process.
  • Add a longer boom or more elements. A larger design can, in some cases, offer both higher gain and improved F/B, though not automatically. See how many elements a Yagi needs.

If you simply have a strong signal behind you, there are non-antenna options too, such as moving the antenna so a building shields it from the interferer, or adding a filter.

The trade-offs

Peak front-to-back ratio, maximum forward gain, low SWR and wide bandwidth do not all happen at the same settings. Typically:

  • Tuning for the best F/B can reduce forward gain a little.
  • A deep F/B null can be narrow in frequency, so it is strong at one frequency but poor at the band edges.
  • Tuning for maximum gain can leave the rear pattern messy.
  • Changes that improve F/B can lower the feedpoint impedance and require a different match.

For single-frequency use, a narrow, carefully tuned design may suit you. For wideband TV, accept a more modest figure.

Measuring it

  • By modeling. The easiest way. The pattern plot shows the forward gain and the rear response.
  • By measurement. Use a field-strength meter or a receiver with a signal-strength readout. Compare the reading with the antenna pointed at a steady transmitter and then rotated 180 degrees. Use a test signal far enough away, and keep people and metal objects out of the area. Results are approximate.
  • By checking real-world behavior. If an interfering signal drops noticeably when you turn the antenna’s back to it, the F/B is doing its job.

Real-world factors

The ratio on a datasheet applies to an antenna in free space. In practice, the nearby roof, mast, other antennas, gutters, wiring and trees can reflect or re-radiate signals and fill in the rear null. Mounting height and location also change the pattern. Mounting the antenna a little away from large metal objects, keeping the boom clear of the mast head where possible, and matching the antenna properly will help you get closer to the rated figure. A poor feed-line arrangement can also pick up signals directly, bypassing the antenna’s rear rejection.

The complete guide to yagi antenna design

Yagi Antenna Design Basics
Read the guide

Keep exploring

Guides from other topics

All topics →