What a wire Yagi is and when it makes sense
A wire Yagi uses wire for the elements instead of aluminum tubing. The wires are strung between supports such as trees, masts or poles, and in the simplest form the “boom” is just the line of supports or a set of spacer ropes. It follows the same principle as a regular Yagi antenna: a driven element, a slightly longer reflector behind it, and optionally one or more slightly shorter directors in front.
Wire Yagis suit amateur radio operators on lower HF bands, where a full-size metal beam would be very large, heavy and expensive. Cost and weight are the main advantages. The main drawbacks are that the beam usually points in one fixed direction, the elements move in the wind, and tuning takes patience.
Choosing a band and a layout
Two- and three-element layouts are the most practical. A two-element wire Yagi, reflector plus driven element, is simpler and needs less space. A three-element one adds a director for more gain and a narrower beam. How much to add is covered in how many elements a Yagi needs.
Decide first:
- The band, and the part of it you use most, since the design will be tuned to a narrow range.
- Where you want the beam to point.
- Whether you can hang the elements horizontally, as a sloper or inverted shape, or as a rotated array on a mast.
- How high the elements can go. Height above ground changes the radiation pattern and feedpoint impedance, so lower installs behave less predictably.
Calculating element lengths and spacing
For a bare wire, a common starting formula for a half-wave dipole in feet is 468 divided by the frequency in MHz. In metres, it is about 142.6 divided by the frequency in MHz. For the rest of the elements:
- The reflector is roughly 5% longer than the driven element.
- Directors are roughly 5% shorter than the driven element.
- Spacing between elements is often about 0.15 to 0.2 wavelength for compact designs. Wider spacing generally gives a feedpoint impedance closer to what you want, but requires more space.
Worked example for 20 meters, centered near 14.15 MHz. These are starting points only.
- Driven element: 468 / 14.15 is about 33.1 feet.
- Reflector: about 5% longer, so around 34.7 feet.
- Director (if used): about 5% shorter, so around 31.4 feet.
- Wavelength: about 984 / 14.15, or roughly 69.5 feet. A spacing of 0.15 wavelength is about 10.4 feet; 0.2 wavelength is about 13.9 feet.
Wire diameter, insulation, height above ground and nearby objects all shift the resonant length. Insulated wire usually resonates at a shorter length than bare wire, so cut elements a little long and trim. A modeling program such as 4nec2 or MMANA-GAL can account for height and wire size and is worth the time.
Wire, insulators and supports
- Wire. Stranded copper or copper-clad steel in the 12 to 14 AWG range is a common choice for HF antennas. Copper-clad steel stretches less.
- Insulators. Use proper insulators at each element end and at the center. Ceramic or UV-stable plastic is typical.
- Spreader ropes. Use non-conductive, UV-resistant rope. Avoid materials that stretch heavily or soak up water.
- Supports. Trees move and grow, so plan for sag and sway. Pulleys with counterweights or tensioners help keep elements at a consistent length and position.
The more the elements sag or sway, the more the design drifts from its calculated tuning. Keep tension reasonable and check the antenna after storms.
Feeding the driven element
A parasitic array lowers the feedpoint impedance of the driven element, often well below 50 ohms. Common ways to cope with this in a wire Yagi:
- Use a folded dipole as the driven element. This raises the impedance, often by about a factor of four. It pairs with a 4:1 balun.
- Use a balun at the feedpoint to connect balanced elements to unbalanced coax, which also helps keep common-mode current off the coax.
- Add a matching network such as a hairpin or similar if modeling shows the impedance is too low.
Check what impedance your model predicts before choosing a balun ratio.
Building and raising it
- Cut each element a little long and mark its center.
- Attach the center insulator or balun to the driven element.
- Attach end insulators and rope to each element. Label each one, since the reflector, driven element and director look similar.
- Lay out the spacing on the ground with a tape measure, then confirm again once hung.
- Hoist the elements one at a time, keeping tension even.
- Make sure the feed line leaves the antenna at a right angle to the elements for a few feet if possible, and is supported so it does not pull on the center.
Tuning and checking SWR
Use an antenna analyzer or SWR meter to look at the match across the band. The usual approach is to trim the driven element for resonance and then adjust the reflector and director in small steps while watching SWR. If resonance is too low in frequency, the element is too long. If it is too high, it is too short. Trim in small steps because you cannot add wire back.
SWR only tells you about the match. It does not show whether the beam is pointing the right way or how much front-to-back ratio you have. For that, compare signals from stations in front of and behind the antenna, or rely on a model. See what front-to-back ratio means.
Limitations
- The beam is fixed unless you rig the elements to rotate.
- Bandwidth is narrow, particularly for a well-tuned design.
- Wind and ice change element shape and tension.
- Gain is modest for two or three elements, and real-world gain depends strongly on height and ground.
- Wire beams take more time to tune than aluminum ones.
Safety
Putting up antennas carries real risks, including falls and contact with overhead power lines, which can be fatal. Keep the antenna, ropes and any mast well clear of power lines, including if something falls. Avoid raising antennas in wind, rain or thunderstorms, wear eye protection, and work with a helper. Ground the feed line and follow local electrical codes and any rules for your area, including permission from landlords or homeowner associations.