Yagi Antenna Design

Designing Yagis for Wi-Fi and 1800 MHz: Using a Yagi Calculator

How to use a Yagi calculator for a DIY Wi-Fi or 1800 MHz antenna: inputs, element sizes at 2.4 GHz and 1800 MHz, tolerances, materials and legal cautions.

On this page
  1. What a Yagi calculator does
  2. Inputs you will need
  3. Wavelength and element size at 2.4 GHz and 1800 MHz
  4. Designing a Wi-Fi Yagi at 2.4 GHz
  5. Designing a Yagi for 1800 MHz
  6. Materials, connectors and cable
  7. Why tolerances matter
  8. Checking the result
  9. Legal and practical cautions

What a Yagi calculator does

A Yagi calculator takes a design frequency and a few physical details, and returns the length and position of each element along the boom. Some are simple web forms. Others are desktop programs based on published designs, such as the long-boom Yagi designs associated with DL6WU. Treat the output as a good starting point, not a guarantee. The underlying Yagi design principles still apply: the calculator is just doing the arithmetic for you.

Inputs you will need

Most calculators ask for some or all of these:

  • Design frequency. Pick the center of the range you want to use.
  • Number of elements. More elements give more gain and a narrower beam. See how many elements a Yagi needs.
  • Element diameter. The rod, wire or tube you will use. Thickness affects the best length.
  • Boom diameter and material. A metal boom that elements pass through needs a length correction.
  • Whether elements are insulated from the boom or touch it.
  • Units. Check whether results are in millimetres, centimetres or inches, and whether lengths are full element lengths or half-lengths measured from the boom.

Check the result against a second calculator if you can. Different tools can give slightly different answers, and a large disagreement points to a wrong input.

Wavelength and element size at 2.4 GHz and 1800 MHz

Free-space wavelength in centimetres is about 30,000 divided by the frequency in MHz.

Frequency Wavelength Approx. half-wave
2437 MHz (Wi-Fi channel 6) about 12.3 cm about 6.2 cm
1795 MHz (mid-point of the 1710 to 1880 MHz range) about 16.7 cm about 8.4 cm

Real driven elements come out somewhat shorter than the half-wave figure because of end effects, often by around 5%, depending on diameter. So an element for 2.4 GHz is around 5.5 to 6 cm, and one for 1800 MHz is around 8 cm. A calculator with the right diameters gives better numbers than these estimates.

Designing a Wi-Fi Yagi at 2.4 GHz

The 2.4 GHz Wi-Fi band spans roughly 2400 to 2483.5 MHz, and the range is fairly narrow compared with the center frequency, so a standard Yagi covers it comfortably.

  1. Enter 2437 MHz as the design frequency, or the center of the channels you use.
  2. Choose an element count. Home-built Wi-Fi Yagis often use around 8 to 15 elements, though results vary with build accuracy.
  3. Enter your rod diameter and boom details.
  4. Note the reflector, driven element and director lengths and their positions along the boom.
  5. Build, then test.

Wi-Fi is typically vertically polarized on most client devices and access points, but check your equipment. If one end is vertical and the other is horizontal, you lose signal. Antennas on many routers are adjustable, so you can often just rotate the Yagi to match.

Designing a Yagi for 1800 MHz

1800 MHz is used for mobile networks in many countries, commonly as LTE band 3 (1710 to 1785 MHz uplink, 1805 to 1880 MHz downlink) and for GSM 1800. Bands and usage vary by country, so check what your carrier uses before designing.

The 1710 to 1880 MHz range is wider in proportion than the Wi-Fi band, about 10% of the center frequency. A simple Yagi tuned tightly for one spot can fall off at the edges. Options include:

  • Enter the middle of the range, and accept a bit less gain at the edges.
  • Use thicker elements to widen bandwidth.
  • Use a design built for broadband performance. See the broadband section of our Yagi design basics.
  • Choose a smaller number of elements, which is generally less sensitive.

Cellular modems and phones often use two antennas (MIMO). Some users build two Yagis, or a cross-polarized pair, so each sees a separate polarization, but this depends on your modem and is worth checking against its documentation.

Materials, connectors and cable

  • Elements. Brass rod, copper wire and welding rod are common. They need to be straight and cut accurately.
  • Boom. Wood, plastic or metal. Wood and plastic need less boom correction but can absorb moisture or change over time.
  • Connectors. SMA, N-type, or the connector on your device. Some cellular modems use TS-9, CRC9 or SMA ports.
  • Cable. Coax loses more signal at higher frequencies. Keep the run short, and use low-loss cable if it must be long. Long runs of cheap coax can cancel the gain of the antenna.
  • Feedpoint. The driven element is often built as a folded dipole or soldered directly to a connector, depending on the calculator’s design.

Why tolerances matter

At 2.4 GHz and 1800 MHz, the elements are only a few centimetres long. An error of one millimetre is a sizeable fraction of the element, and positions along the boom matter just as much. A few millimetres of error can shift the best frequency of a Yagi enough to cut performance noticeably.

To improve repeatability:

  • Mark the boom with a sharp tool and a ruler or calipers.
  • Cut all elements of the same length from the same stock together.
  • Make sure each element is perpendicular to the boom and centered.
  • Check the connector soldering and keep it short.

Checking the result

With an antenna analyzer or a VNA you can look at SWR or return loss across the band. If the best match sits above or below your target frequency, small changes to the driven element or its match can bring it back. Without equipment, compare signal strength or throughput before and after, and rotate and tilt the antenna to find the best direction. Treat any signal reading as relative. The Yagi’s gain also narrows its beam, so aim matters.

  • Wi-Fi. Regulations in many countries limit output power or the effective radiated power on unlicensed bands. A high-gain antenna on a transmitter can push you beyond those limits, so check your local rules.
  • Cellular. A passive antenna connected to a phone or modem is usually treated differently from a signal booster or repeater, which are regulated in many places. Check the rules in your country and your carrier’s terms before connecting anything that amplifies.
  • Mounting. Outdoor antennas need weatherproofing and safe mounting, away from power lines.
  • Expectations. Gain does not create signal. A Yagi helps most when pointed at a tower or access point with a clear path.

The complete guide to yagi antenna design

Yagi Antenna Design Basics
Read the guide

Keep exploring

Guides from other topics

All topics →