Short answer
The best way to get Wi-Fi to a detached garage or shed depends on two things: how far it is from the house, and what stands between them. A close garage may be reached by an indoor extender. A building across the yard usually needs an outdoor access point or mesh node. A distant or heavily obstructed one is better served by a point-to-point wireless bridge or a cable. Start with the simplest option and move up only if it does not work.
Step 1: measure and test
- Measure the distance from the router, or from the nearest house wall that faces the outbuilding.
- Walk to the garage with your phone and a free Wi-Fi analyzer app. Note the signal at the door, inside, and at the spot where you need it.
- Note what is in the path: walls, windows, trees, vehicles, metal siding or a metal roof.
If you already get a weak but usable signal in the garage, an extender may be enough. If you get nothing, plan for something outdoors or wired.
Close garage: extender or mesh node
An indoor extender or mesh node plugged in on the house wall that faces the garage can sometimes carry the signal across. Two rules apply:
- The extender can only pass on a signal it receives. Place it where it still gets a strong signal from the router, not out near the garage where the signal is already weak.
- Wireless hops lose speed, so expect lower throughput than in the house.
This is the cheapest and easiest first try. If the result is patchy, move on. See also how far Wi-Fi reaches outside your house for what to expect at the edge of coverage, and extenders for larger areas.
Across the yard: outdoor access point or mesh node
When an indoor unit cannot reach, move the radio outside. Options include:
- Outdoor access point: a weatherproof unit mounted on the house wall facing the garage, wired to your network and powered by PoE.
- Outdoor-rated mesh node: if your home mesh system offers one, it joins the existing network, and some use wired power.
- Outdoor extender: works in repeater mode if you have no mesh system, but it still relies on receiving a good signal from the house.
Mount the unit with a clear view toward the garage, and use equipment with an ingress rating suited to rain and dust. Manufacturers give their own coverage figures, but those are best-case and depend on line of sight.
Long gap: use a bridge
For a shop or barn too far away for an extender, use a point-to-point bridge. Two units face each other, one on each building, and carry your network across. At the garage end, add a switch or access point to serve devices inside. Our guide, how to link two buildings with a point-to-point Wi-Fi bridge, covers line of sight, aiming and settings. Distance claims vary, so check what the manufacturer says is required for a clear link.
Wired options
Wired links are fast and stable. They usually take more effort.
- Outdoor Ethernet cable: use cable rated for outdoor or direct-burial use, and often conduit, with a maximum run of about 100 metres (328 feet). Burying cable may need permits or have rules about depth. Check your local codes, and call your utility locating service before digging.
- Fibre with media converters: carries data over long distances and does not conduct electricity between buildings, which avoids ground-loop and surge problems. Fibre ends need care to install, so pre-terminated cable is easier.
- Powerline adapters: use existing electrical wiring. They can work if the garage is on the same circuit or panel path, but real-world speeds are often well below the advertised figure, and some wiring or devices degrade them. Try one if you can return it.
- PoE access point in the garage: if Ethernet reaches the garage, a PoE access point means you only need the cable, not a power outlet, at the far end.
A metal cable between buildings can pick up lightning surges. Ask a qualified electrician about grounding and surge protection for any run between buildings.
If the garage is metal
Metal walls and roofs block much of a Wi-Fi signal. A radio inside the house may not reach a device inside a metal building. Mount an outdoor unit outside the building with a view toward the house, and run Ethernet through the wall to an access point inside. A bridge unit mounted on the outside and connected by cable to an inside access point follows the same idea.
Power and weather
- Outdoor radios need power. PoE sends power and data over one cable, with the injector or switch indoors.
- If there is no outdoor outlet, PoE is often the easiest solution. Do not install a PoE injector outdoors unless it is rated for it.
- Seal outdoor connectors, and leave a drip loop in cables.
- Work at height and electrical work should be done by qualified people where required.
Quick decision guide
| Situation | Usually best |
|---|---|
| Garage close, weak but usable signal | Indoor extender or mesh node facing the garage |
| Across the yard, line of sight | Outdoor access point or outdoor mesh node |
| Far building or poor path | Point-to-point bridge plus access point inside |
| Want the fastest, most stable link | Buried Ethernet or fibre |
| Metal building | Outdoor unit with cable to an indoor access point |
If you want to understand the antennas behind these choices, see our overview of long-range Wi-Fi antennas.