Set realistic expectations
A homemade directional antenna can improve a Wi-Fi link in one direction, usually by focusing signal the same way a commercial panel does. It cannot create range from nothing, and results depend heavily on how carefully you build and aim it. Many builders see a modest improvement, and some see none. Before you start, decide whether a purchased long-range Wi-Fi antenna would serve you better. Basic commercial panels are inexpensive and are tested at the factory.
A can antenna is still a good learning project, and it works best for a fixed spot, such as pointing at a nearby building.
2.4 GHz antenna design basics
- Wavelength: at 2.4 GHz the wavelength is about 12 cm. A quarter-wave element is roughly 3 cm, and a half-wave element about 6 cm. In practice, elements are trimmed a little shorter than the free-space figure.
- Resonance: an antenna works well only when its dimensions match the band. A 2.4 GHz design does not work well on 5 GHz, and the reverse is also true.
- Impedance: Wi-Fi equipment and cable are designed for 50 ohms. A mismatch reflects power back and lowers efficiency.
- Polarization: most Wi-Fi antennas are linearly polarized. For best results, both ends of a link should use the same orientation, vertical or horizontal.
- Directional vs omni: directional designs (can, panel, Yagi) focus energy. Omnidirectional designs spread it around.
- Crowded band: 2.4 GHz is shared with many other devices, so interference can hide any gain.
Option 1: can antenna (cantenna)
This is the classic project. A metal can acts as a waveguide, and a short probe inside launches the signal.
What you need
- A metal can, with a diameter of roughly 3 inches or more (check a cantenna calculator for the right size and probe position)
- An N-type female panel-mount connector
- A short piece of stiff copper wire or brass rod for the probe
- A pigtail cable from the N connector to your router, adapter or access point connector
- Drill, ruler, marker, soldering iron, and small nuts and bolts
Steps
- Find the dimensions. Use a cantenna calculator with your can’s inner diameter. It gives the probe position (a distance from the closed end of the can) and the probe length.
- Drill the connector hole at the calculated position, matching the connector size. Drill mounting holes if the connector needs bolts.
- Cut and solder the probe to the connector’s centre pin, keeping it straight and the correct length.
- Mount the connector with the bolt heads inside and the nuts outside, so nothing blocks the interior.
- Connect the pigtail to your router or adapter. Use a connector that matches your equipment, as covered in SMA versus RP-SMA connectors.
- Aim the can at your target, and try rotating it. Because the antenna is linearly polarized, rotation changes the result.
Keep the pigtail short. At Wi-Fi frequencies, thin cable can waste a meaningful part of any gain you create.
Option 2: simple reflector for an existing antenna
A curved metal reflector behind a router antenna can direct more signal forward and reduce it behind. It is easy to try and safe to remove. Keep it behind the antenna, never wrapped around it, and do not cover the router’s vents. We examine this idea in does aluminum foil really boost Wi-Fi.
Can a TV antenna be used for Wi-Fi?
Generally no. TV antennas are tuned for VHF and UHF television frequencies, far below the 2.4 and 5 GHz Wi-Fi bands, so they do not resonate there. Using one in place of a Wi-Fi antenna will usually do nothing useful and can mismatch your radio. A Wi-Fi antenna built for the right band is the correct tool.
Making Wi-Fi stronger on a laptop
Before building anything, try these:
- Move closer, or rotate the laptop and router antennas.
- Switch bands. Use 2.4 GHz for range and 5 GHz for speed at closer range.
- Use a USB Wi-Fi adapter that has a detachable external antenna, so you can add a better one.
- Update drivers and reduce interference from other devices.
Reaching a building 200 feet away
At roughly 60 metres, a clear line of sight, a pair of directional antennas or outdoor bridge units, and careful aiming usually work. A single DIY antenna at one end will often struggle because the far device cannot reply as strongly. See how to link two buildings with a point-to-point Wi-Fi bridge and getting Wi-Fi to a detached garage or shed.
Test, safety and rules
- Take signal readings before and after with the same device and the same spot, using a phone Wi-Fi analyzer or your router’s status page.
- Do not add amplifiers or raise transmit power beyond what your local regulations allow.
- Be careful when soldering and when working on roofs or masts. Keep clear of power lines.
- Outdoor installs need weatherproofing and, for exposed cabling, surge protection and grounding.
For what gain figures mean in practice, read Wi-Fi antenna gain versus range.