What a point-to-point bridge is
A point-to-point (PtP) Wi-Fi bridge uses two directional radios, one on each building, that talk only to each other. Together they behave like an Ethernet cable through the air. Plug your network into one end, and the network appears at the other end, where you connect a switch or a Wi-Fi access point to serve devices.
This differs from a range extender, which rebroadcasts Wi-Fi to nearby devices. A bridge is meant for a longer, aimed link between two fixed locations. Many outdoor bridge kits come as a pre-paired set of two units that are configured to connect automatically, and they are often powered over Ethernet (PoE).
Check you have line of sight
Radio links work best with a clear path. Before you buy anything:
- Stand where the first unit will go and look toward the second. Can you see the spot?
- Note anything in between: trees, other buildings, hills, metal roofs.
- Remember trees grow and leaves return in spring. A path that looks clear in winter may be blocked in summer.
- Allow for clearance around the straight line, not just along it. A radio path needs a clear zone, called the Fresnel zone. Over short distances, such as 200 feet, it is narrow, but it widens with distance.
Bridge kits are often quoted for distances of a kilometre or more under clear conditions. That does not mean they will work through trees or other buildings. For very short hops across a yard, the main concern is usually walls and foliage, not distance. For more on range claims, see Wi-Fi antenna gain versus range.
Choose the equipment
- Pre-paired kit: two matched units, usually the easiest option. They are designed to link with little configuration.
- Two separate units: more flexible, but you set one as an access point and the other as a client (station) yourself.
- Band: 5 GHz is commonly used for point-to-point links because it has more channels and is often less crowded than 2.4 GHz, though it does not penetrate obstacles as well. 2.4 GHz can be a fallback when there are trees in the path.
- Weather rating: choose units designed for outdoor use, and check the ingress rating and temperature range.
- Power: check whether the units use PoE and which standard, and whether the injector is in the box.
- Antennas: integrated panel or dish antennas are simplest. Larger external antennas can extend range but add cabling and connectors, as in long-range Wi-Fi antennas.
Also check your local radio rules, since limits on power and the use of certain channels outdoors may apply.
Plan the network
A bridge should pass your network across, not create a second network.
- Keep both ends on the same network (same subnet). Plug the bridge’s near end into your router or switch.
- Do not run a second router at the far end in routing mode unless you want a separate network, since that can create double NAT and make devices hard to reach.
- At the far end, connect a switch, or an access point if you want Wi-Fi in that building. A bridge carries the link, but it is not designed to give good Wi-Fi coverage inside the building.
- Set an admin password on both radios, and change the default Wi-Fi settings.
Install and aim
- Test indoors first. Power both units on a bench, confirm they pair, and note any settings you need.
- Mount high and firmly. Use a wall bracket or pole mount. Make sure it does not sway in wind.
- Point toward each other. Place the units so that their fronts face each other. Panels are polarized, so keep both in the same orientation, as the manual advises.
- Connect cables and power. Run outdoor-rated Ethernet cable from each unit to its PoE injector or switch. Keep a drip loop so water does not run into the connectors.
- Fine-tune aim. Use the signal indicator in the web page or app, and adjust slowly until the signal is best.
- Test throughput. Run a speed test between devices at each end, and check at different times of day.
Cabling, power and lightning
- Standard Ethernet runs are limited to about 100 metres (328 feet), so the cable from each radio to its switch or injector must stay within that.
- The PoE injector normally sits indoors. Do not mount it outdoors unless it is rated for it.
- Outdoor radios on masts or rooftops can be exposed to lightning and surges. Surge protection and grounding for outdoor Ethernet are often recommended, and electrical codes may apply. Consider a qualified installer for any work at height or on grounding systems.
- A wireless link has an advantage here: it does not carry a continuous metal conductor between the buildings, as a long cable run would.
If line of sight is not possible
- Add a mounting pole, or move a unit to a higher point on the building.
- Try a different mounting spot, such as a gable end that faces the other building.
- Consider a wired option. Buried outdoor-rated Ethernet, or fibre, can work and is immune to weather and foliage. See getting Wi-Fi to a detached garage or shed for how the choices compare.
- For a short, clear hop, an outdoor access point or mesh node may do the job, as discussed in how far Wi-Fi reaches outside your house.
Troubleshooting
- No link: check power, then aim and polarization. Make sure both are on the same channel and security settings.
- Low speed: look for obstacles, interference or a poorly aimed unit, and try another channel.
- Drops in bad weather or when trees have leaves: the path may be marginal. Raise the units or change the route.
- Devices at the far end have no IP address: check that the far end is not in router mode and that the cable goes to the right port.