Ham Radio Antennas

How Long Should a 40 Meter Dipole Be? Length Formula and Trimming

A 40 meter dipole is about 65 to 67 feet in total, roughly 33 feet per leg. Use 468 divided by frequency, cut long, then trim with an analyzer for the lowest SWR.

On this page
  1. Quick answer
  2. Why you still need to trim
  3. How to build and cut
  4. How to trim it
  5. Inverted-V and height
  6. Common problems

A half-wave dipole for 40 meters is about 65 to 67 feet (roughly 20 m) long in total, which is about 32.5 to 33.5 feet (around 10 m) per leg. The exact length depends on where in the band you want it to be resonant, and you should always cut it a little long and trim it.

Quick answer

The standard formula for total length in feet is 468 divided by the frequency in MHz. Divide the result by two for each leg.

Frequency Total length Each leg
7.000 MHz (CW and digital end) about 66.9 ft about 33.4 ft
7.100 MHz about 65.9 ft about 33.0 ft
7.150 MHz about 65.5 ft about 32.7 ft
7.200 MHz (phone) about 65.0 ft about 32.5 ft

In metric terms, divide 143 by the frequency in MHz for the total length in metres (about 20 m at 7.1 MHz).

Why you still need to trim

The formula assumes a straight wire in free space. Real antennas differ because of:

  • Wire thickness and insulation, which shorten the electrical length of the wire slightly. Insulated wire usually needs to be a bit shorter than bare wire.
  • Height above ground, which affects resonance.
  • Nearby objects such as trees, buildings and fences.
  • Inverted-V shape, where the ends droop; the resonant length changes a little compared with a flat-top dipole.

That is why you should add extra wire for tying off at the insulators, plus some spare, and trim during tuning. A few feet of extra length on each leg is usual.

How to build and cut

  1. Cut two lengths of wire, each leg plus extra for the knot or loop at the centre and at the end, such as an extra foot or two at each end.
  2. Attach each leg to a centre insulator with a balun or choke, and to an end insulator at the far end.
  3. Hang it as high as you can, with the ends supported by non-conductive rope. Keep it away from power lines.
  4. Connect coax via a 1:1 balun or common mode choke.

How to trim it

  1. Sweep the band with an antenna analyzer and note the frequency where the SWR is lowest.
  2. If the lowest point is below where you want it, the antenna is too long. If it is above, it is too short.
  3. Use this approximation: new length = current length multiplied by (current resonant frequency divided by target frequency). For example, if the dip is at 6.9 MHz and you want 7.1 MHz, shorten the total by about 3 per cent, or around 2 feet in total, so about a foot per leg.
  4. Make small changes, retest and repeat. Trim both legs equally so the antenna stays balanced.

If you only have an SWR meter, measure at a few frequencies across the band and find the minimum. See what a good SWR is.

Inverted-V and height

An inverted-V needs less horizontal space and only one tall support, and it is popular for 40 m. Keep the angle between the legs wide, around 90 degrees or more, and expect to trim after raising it. Higher is generally better, though a 40 m dipole can work from lower heights for regional contacts.

Common problems

  • SWR is high everywhere. Check connectors and coax, and consider common-mode current.
  • Resonance moves after weather or tree growth. Recheck seasonally.
  • Need more than one band. Consider a multiband option or a tuner. See whether you need an ATU.

For a wider look at what else you might choose, see our HF antenna guide.

The complete guide to ham radio antennas

HF Antennas for Ham Radio: Choosing the Right Type
Read the guide

Keep exploring

Guides from other topics

All topics →