Ham Radio Antennas

Common Mode Chokes for Ham Antennas: What They Do and How to Make One

A common mode choke stops RF flowing on the outside of coax. Learn the symptoms, where to place chokes, and how to make one with ferrite toroids, beads or coiled coax.

On this page
  1. What common-mode current is
  2. Symptoms
  3. Where to put chokes
  4. Choosing the ferrite
  5. DIY: toroid choke
  6. DIY: bead choke
  7. DIY: coiled coax choke
  8. Power and heating
  9. Testing

A common mode choke is a component that blocks RF current from flowing along the outside of your coax shield while leaving the signal inside the cable untouched. It is one of the cheapest and most effective fixes for RF in the shack, noise and unpredictable SWR. You can make one yourself using a ferrite toroid, ferrite beads or a coil of coax.

What common-mode current is

Coax is supposed to keep all RF inside: current flows one way on the centre conductor and the opposite way on the inside of the shield. If the antenna is not perfectly balanced, or something else couples to the cable, a second current can flow on the outside of the shield. That is common-mode current. It turns your coax into part of the antenna, picks up household noise and can bring RF back into your equipment.

Symptoms

  • RF feedback, buzzing or distorted audio when you transmit.
  • SWR that changes when you touch or move the coax.
  • High receive noise that changes when you move the cable.
  • Interference to nearby electronics.
  • Antennas without a balanced feed or counterpoise, such as end-fed wires, are especially prone to this.

Where to put chokes

  • At the antenna feed point, as close as practical, which keeps the antenna itself clean.
  • Near the shack entrance, to stop RF travelling into the room.
  • At a few additional points on long runs, if problems continue.

Choosing the ferrite

Ferrite comes in different mixes designed for different frequency ranges. Mix 31 is commonly recommended for HF, with mix 43 used for higher HF and VHF. Pick a material and size suited to your band, and follow a published design for the specific bands you use, since the effective range of any single choke is limited.

DIY: toroid choke

The usual approach is to wind the coax itself through a large ferrite toroid.

  1. Use a large toroid such as the FT240-size in mix 31, which is a common choice for HF.
  2. Wind a number of turns of coax through the core. A typical guide is somewhere around 7 to 10 turns, which suits small-diameter coax like RG-58 or RG-8X. Larger coax means fewer turns fit.
  3. Keep the turns separated and in a neat spiral rather than overlapping, which can reduce performance.
  4. Secure the winding with cable ties or tape.
  5. Seal the assembly from moisture if used outdoors.

DIY: bead choke

Slip a stack of clamp-on or slip-on ferrite beads over the coax. It is simple, but you need many beads on a thin cable to get a similar effect, and the beads must fit the cable diameter. Consider a published design for the number of beads for your band and cable type.

DIY: coiled coax choke

Coiling a few turns of coax into a loop can form a basic air choke. It is cheap but is narrow-band, working best near the frequency it was built for, and is generally less effective than ferrite. It is a stopgap for one band, not a solution for several.

Power and heating

A choke that is too small or the wrong material can heat up with sustained transmission, especially at higher power or in digital modes. Check it is not warm after a long transmission, use larger cores for higher power and follow the design power rating.

Testing

You can judge the effect by watching SWR stability, the noise level and RF in the shack. For a more exact measure, a vector network analyzer can measure the choke’s impedance. See how to use an antenna analyzer for measurement basics.

Chokes pair well with a good SWR check, a proper antenna tuner arrangement and a sound feedline layout. For the wider picture, see our HF antenna guide.

The complete guide to ham radio antennas

HF Antennas for Ham Radio: Choosing the Right Type
Read the guide

Keep exploring

Guides from other topics

All topics →