Installation and Wiring

How to Ground a TV Antenna Mast and Protect It From Lightning

How to ground a TV antenna mast and coax: ground wire to the mast, a coax grounding block, bonding to your home's electrical ground, and when to call an electrician.

On this page
  1. Why ground an outdoor antenna?
  2. Safety first
  3. What you need
  4. Step 1: Ground the mast
  5. Step 2: Ground the coax
  6. Step 3: Connect to the home’s grounding system
  7. Special cases
  8. Inspect periodically

Why ground an outdoor antenna?

An outdoor antenna and its mast are metal objects standing up high, connected by cable to your TV. Grounding them gives static charge and stray voltage a controlled path to earth rather than through your equipment or home wiring. In the United States, the National Electrical Code (NEC) addresses antenna grounding in Article 810, and it generally calls for masts and coax lead-ins to be grounded and bonded to the building’s grounding system. Local rules may differ, so check with your local building department or an electrician.

Grounding is not a guarantee. It lowers risk and helps with static buildup and nearby strikes, but no residential ground can promise protection against a direct lightning hit.

Safety first

This job involves ladders, roofs and sometimes electrical systems, so be cautious.

  • Stay well away from overhead power lines. Check your antenna manual for the clearance it recommends.
  • Do not work in wet, windy or stormy conditions.
  • Use a non-metallic ladder and a helper.
  • Do not open your electrical panel or make connections inside it. If the ground wire must connect to your service equipment, ask a licensed electrician.

For the overall installation, see how to install an outdoor TV antenna.

What you need

  • Ground wire: commonly 10 AWG copper or heavier (many instructions mention #10 copper or #8 aluminum as a minimum). Follow your local code.
  • Mast ground clamp or lug
  • A coax grounding block (sometimes sold as an antenna discharge unit or lightning arrestor), rated for coax
  • Wire standoffs or staples to run the wire down the house
  • A ground rod and clamp, if your home needs one, plus any bonding hardware
  • Sandpaper or a wire brush

Step 1: Ground the mast

  1. Clean the contact point. Scrape off paint, rust or coating on the mast so the clamp touches bare metal.
  2. Attach the clamp to the mast and secure the ground wire to it.
  3. Run the wire down toward the ground point using a fairly straight path, avoiding sharp bends, and supporting it with standoffs every few feet.
  4. Avoid splices in the wire between the mast and the grounding point where possible.

Step 2: Ground the coax

  1. Install a grounding block on the coax, outside, as close as practical to where the cable enters the house.
  2. Connect the coax from the antenna to one side of the block and the coax continuing toward the TV to the other side.
  3. Connect a ground wire from the block to the grounding point.

Step 3: Connect to the home’s grounding system

The ground wires should end up bonded to your home’s electrical grounding system. This is often an intersystem bonding termination or the main grounding electrode conductor near your electrical meter or panel, or a ground rod that is bonded to it. Keeping everything on the same grounding system matters so there is no voltage difference between systems during a surge. If you add a separate ground rod, it generally needs to be bonded to the main electrical ground rather than left isolated.

Because this step touches the home’s electrical service, many homeowners hire an electrician for it, even if they do everything else themselves.

Special cases

  • PVC masts cannot be grounded. If your mast is plastic, run a ground wire from the metal parts of the antenna assembly itself.
  • Attic and indoor antennas are generally not subject to the same mast grounding as outdoor installs, but check the manual and local code. Using a surge protector for electronics is a good idea in general.
  • Amplifiers and power inserters should be installed according to their instructions, with the grounding block placed on the outdoor cable before it enters the house. See how to install a TV antenna amplifier.

Inspect periodically

Check connections once or twice a year for corrosion or loose clamps, and after severe storms. If the antenna or equipment has been struck or damaged, have it checked before using it again.

Related: RG6 vs RG59 coax for a TV antenna explains the cable that the grounding block connects to.

The complete guide to installation and wiring

How to Install an Outdoor TV Antenna
Read the guide

Keep exploring

Guides from other topics

All topics →