FM Radio Antennas

75 Ohm vs 300 Ohm FM Antenna Connections and When You Need a Balun

Learn the difference between 75 ohm coax and 300 ohm twin-lead FM antenna connections, how to tell which your receiver uses, and when a 300-to-75 ohm balun helps.

On this page
  1. Short answer
  2. What the numbers mean
  3. What you will find on receivers
  4. What a balun does
  5. Decision guide
  6. Connecting step by step
  7. What if you skip the balun?
  8. Buying notes

Short answer

FM antennas and receivers use one of two standard connection types: 75 ohm unbalanced coaxial cable, and 300 ohm balanced twin-lead (flat ribbon cable) connected to two screws. If your antenna and receiver use the same type, connect them directly. If they differ, a small matching transformer called a balun solves it. Modern equipment mostly uses 75 ohm coax, so the question usually arises with older gear.

What the numbers mean

The ohm figures describe the impedance of the cable and antenna, a measure of how the signal sees the connection. Matching impedances moves the signal along with minimal loss and reflections.

  • 75 ohm coax is unbalanced: one central conductor surrounded by a shield. Typical cable types, such as RG-6, use F-type connectors.
  • 300 ohm twin-lead is balanced: two parallel conductors in flat ribbon, with neither conductor shielded. It connects to a pair of screw terminals.

A half-wave dipole has an impedance near 70–75 ohms, and a folded dipole about 300 ohms. That is why both standards have survived. For more on these antenna types, see FM dipole antennas.

What you will find on receivers

  • A push-on or screw-on coax connector marked “75 ohm”: common on modern receivers. In North America this is often an F connector; elsewhere other coax connector types are used, and some European equipment uses a different coax plug.
  • Two screw terminals marked “300 ohm” or “FM ANT”: found on many older receivers.
  • Both: some receivers have both connection types, and the 300 ohm terminals may be an alternative input.
  • A short wire lead: many receivers ship with a simple wire dipole attached to the screws or a socket.

Look at the markings on the back of your receiver, and check the manual if the connection is unlabelled.

What a balun does

“Balun” stands for balanced-to-unbalanced. A common FM version is a 300 ohm to 75 ohm matching transformer, with a ratio of 4:1, which connects balanced twin-lead to unbalanced coax. It is a small device, often a plastic box with two screw terminals or two spade lugs on one side and a coax connector on the other. In some designs, it is built into the end of a cable, or it plugs into the back of the antenna.

Decision guide

Your antenna Your receiver input What to do
75 ohm coax 75 ohm coax Connect directly, using an adapter if the connectors differ
300 ohm twin-lead 300 ohm screws Connect directly
300 ohm twin-lead 75 ohm coax Use a 300-to-75 ohm balun
75 ohm coax 300 ohm screws Use a 75-to-300 ohm matching transformer

Connecting step by step

  1. Identify the type of cable on your antenna and the input on your receiver.
  2. If they match, connect them, using a connector adapter only if the plug styles differ.
  3. If they do not match, fit the matching transformer at the receiver end, with the 300 ohm side on the twin-lead or screw terminals and the 75 ohm side on the coax.
  4. Do not strip and join the twin-lead to coax by hand without a transformer if you can avoid it.
  5. Tighten connections and keep the cable away from power cords.

If you share an antenna between a TV and a radio with a splitter, see can you use a TV antenna for FM radio.

What if you skip the balun?

Connecting a mismatched antenna directly will often still work, particularly on strong local stations, because FM receivers are fairly forgiving. A mismatch can, however, reduce the signal reaching the tuner and may make balanced lines pick up noise. If you have a weak signal, or you notice hiss or poor stereo, fitting the correct transformer is a cheap and worthwhile improvement. Check how to fix static and poor FM reception at home if problems continue.

Buying notes

  • Buy a transformer rated for FM frequencies. Some devices sold for TV may be intended for TV bands only; check the specification.
  • Look for the right connector on both sides, such as F-type or another type to match your receiver.
  • A simple transformer is inexpensive, so there is no need to spend heavily.
  • Avoid transformers with built-in amplifiers unless you need one.

For the overall picture, see our FM radio antenna guide.

The complete guide to fm radio antennas

FM Radio Antennas: Indoor vs Outdoor and What to Buy
Read the guide

Keep exploring

Guides from other topics

All topics →