What an FM dipole is
A dipole is one of the simplest antennas: two equal lengths of conductor, usually wire, fed at the centre. For FM broadcast reception, the most common version is a half-wave dipole cut for the middle of the FM band. Many receivers ship with a small T-shaped wire or twin-lead antenna that is, in effect, a dipole.
If you want the general concept first, see what is a dipole antenna.
How it works
Each half of the dipole is roughly a quarter of a wavelength long. When a radio wave passes, it induces a small current in the wire, and at the right length the antenna resonates, giving the strongest response near its design frequency. A dipole is also directional in a gentle way: it is most sensitive broadside (at right angles to the wire) and receives little off the ends of the wire.
An ordinary half-wave dipole has an impedance of roughly 70 to 75 ohms at its centre, which fits 75 ohm coax reasonably well. A folded dipole, which uses a looped conductor, presents about 300 ohms, matching the older twin-lead standard. More on this in 75 ohm vs 300 ohm FM antenna connections.
Length calculation for FM
The usual rule of thumb for the total length of a wire half-wave dipole is:
- Feet: 468 ÷ frequency in MHz
- Metres: about 142.5 ÷ frequency in MHz
For a design frequency of 98 MHz (near the middle of the FM band), the total comes to about 4.8 feet (1.45 m), so each leg is about 2.4 feet (about 73 cm). The FM band is wide in percentage terms, but a dipole is fairly broadband, so a single middle-of-the-band length works acceptably across most of it. If you listen mainly to one end of the band, you can cut for that frequency instead.
These figures are approximations. Real-world conditions, wire insulation and nearby objects shift the optimum slightly, so treat the numbers as a starting point.
Materials
- Two lengths of wire about 2.4 ft (73 cm) each
- 75 ohm coax (such as RG-6) or 300 ohm twin-lead, depending on your receiver’s input
- A matching transformer if you are connecting coax to 300 ohm terminals
- Insulating material for the centre support, such as a small plastic block, plus tape or heat-shrink
- Tape, ties or hooks for mounting
Build steps for a simple T-dipole
- Cut two equal wire lengths (about 73 cm each for the middle of the band).
- Mount them in a straight line with a small gap (about 1 cm or less) between them at the centre.
- Connect one wire to the centre conductor and the other to the braid of the coax. If you are using twin-lead, connect one wire to each conductor.
- Insulate and strain-relieve the centre joint so the cable does not pull on the connections.
- Connect the other end to your receiver, using a balun or transformer if the connector types differ.
The “T” shape comes from hanging the two wires horizontally with the feed line dropping from the middle. The wires can also be arranged in a V shape if space is short, at the cost of a little performance.
Mounting and orientation
- Hang it horizontally, as high and as clear of metal objects as you can manage.
- Rotate the antenna so the wire is at right angles to the direction of the stations you want. If your stations are in different directions, rotate it while listening to the weakest one.
- Keep the feed line away from power cables where possible.
If you plan to put it outdoors, use outdoor-rated wire and seal the connections. Take care around power lines, and see the safety notes in the FM radio antenna guide.
Folded dipoles
A folded dipole uses a wire loop and gives better bandwidth and roughly 300 ohms impedance, which is why 300 ohm twin-lead is often used to make one. Many listeners build a folded dipole out of twin-lead by shorting and joining the far ends of a length of twin-lead and cutting the feed point in one conductor. It is a popular DIY design because it uses ordinary parts, but you should confirm the exact design and dimensions from a trusted source before building.
Making a 10m dipole
“10m” usually refers to the amateur radio band at about 28 to 29.7 MHz. Using the same formula, a wire half-wave dipole for about 28.4 MHz is roughly 16.5 feet (5 m) in total, or about 8 feet 3 inches (2.5 m) per leg. Treat that as a starting length and trim to suit with an SWR meter. In many countries you need an amateur radio licence to transmit on this band, even though receiving does not require one.
Where dipoles are used
Dipoles are used widely, including for FM and TV reception, shortwave listening, amateur radio, and as the driven element in directional antennas such as Yagis. They are popular because they are inexpensive, easy to build and easy to understand.
Limits
A basic dipole has only modest gain. In weak-signal areas, a directional design such as a Yagi will usually outperform it; see FM DX antennas for long-range reception. For an overall comparison, see which is better, an outdoor or indoor antenna.