Installation and Wiring

RG6 vs RG59 Coax for a TV Antenna: Which Should You Use?

RG6 is generally the better coax for a TV antenna thanks to lower signal loss and better shielding. See how it compares with RG59 and when RG59 is still fine.

On this page
  1. The short answer
  2. How RG6 and RG59 differ
  3. Why RG6 usually wins
  4. When RG59 is acceptable
  5. What to look for in RG6
  6. Connectors
  7. Length and splitting
  8. Which should you buy?

The short answer

For a TV antenna, RG6 is generally the better choice. It is thicker, loses less signal over distance at TV frequencies, and usually has better shielding than RG59. RG59 can still work for short indoor runs, but there is rarely a reason to choose it for a new installation.

How RG6 and RG59 differ

Both are 75-ohm coaxial cables, which is the impedance that TV antennas, splitters and TVs expect. The differences are mostly physical:

RG6 RG59
Impedance 75 ohm 75 ohm
Thickness Thicker Thinner
Center conductor Larger Smaller
Signal loss at high frequencies Lower Higher
Shielding Often better, with dual or quad shield options Often a single braid, though it varies
Flexibility Stiffer More flexible
Typical use Antenna, cable TV and satellite Older analog video, CCTV and short patch cables

Exact specifications depend on the manufacturer, so compare the data sheet if it matters for a long run.

Why RG6 usually wins

  • Lower loss. Signal weakens as it travels along a cable, and thinner cable loses more, particularly at higher frequencies such as UHF channels. RG6 keeps more of a weak antenna signal for the TV.
  • Better shielding. Good shielding helps keep outside noise out of the cable, which matters near routers, LED lights and other electronics. See TV antenna interference from Wi-Fi and how to fix it.
  • Compatibility. Most modern antennas, amplifiers, splitters and grounding blocks are designed around RG6 and its connectors.

When RG59 is acceptable

  • A short indoor run, such as between a splitter and a TV a few feet away, where loss is small.
  • Existing RG59 already in the walls. Test it before replacing it. If reception is good, it may not be worth pulling new cable. If it is marginal, swapping it for RG6 is one of the easier improvements.
  • Tight bends, where the more flexible RG59 is easier to manage.

For long runs, outdoor runs, weak signals or when feeding several TVs through a splitter, choose RG6.

What to look for in RG6

  • Shield type. Dual-shield is common, and quad-shield offers more protection in noisy places but is stiffer.
  • Outdoor-rated jacket. For runs outside, use cable with a UV-resistant jacket. Some cable is rated for direct burial, if applicable.
  • Center conductor. Some RG6 uses copper-clad steel and some solid copper. Either is common for antenna use, but check the product details, especially for runs that also carry power to an amplifier.
  • Brand and specs, rather than price alone, since cheap cable can have thin shielding.

Connectors

Use F-type connectors sized for the cable. RG6 and RG59 use different connector sizes, so a connector made for one may not fit the other well. Compression connectors generally make a tighter, more reliable connection than twist-on types, and weatherproof boots or sealed connectors help outdoors. A loose or poorly crimped connector can cause more problems than the choice of cable.

Length and splitting

Keep the run as short as is practical, and avoid unnecessary connections. Each splitter adds loss, and long runs add more. See how to split a TV antenna signal to multiple TVs for how this affects multi-TV setups and how to install a TV antenna amplifier for making up for loss.

Which should you buy?

If you are starting a new installation, buy RG6 and plan the route before you run it. See how to install an outdoor TV antenna for the whole process, including cable routing and entry into the house.

The complete guide to installation and wiring

How to Install an Outdoor TV Antenna
Read the guide

Keep exploring

Guides from other topics

All topics →