Installation and Wiring

How to Split a TV Antenna Signal to Multiple TVs

Split one TV antenna to several TVs with a coax splitter or distribution amplifier. Learn about signal loss, choosing a splitter, wiring steps and fixes.

On this page
  1. The short answer
  2. How a splitter affects signal
  3. Choosing a splitter
  4. Step-by-step
  5. Adding an amplifier
  6. Powered antennas and power inserters
  7. All TVs share one antenna direction
  8. Alternatives to splitting
  9. Troubleshooting

The short answer

You can feed several TVs from one antenna by running its coax into a splitter and connecting a cable from each splitter output to a TV. The catch is that splitting divides the signal, so each TV receives less than it would on its own. If the original signal is strong, that is usually fine. If it is weak, you may need an amplifier.

How a splitter affects signal

A splitter does not create more signal. A common 2-way splitter loses roughly 3.5 dB on each output, and a 4-way splitter roughly 7 dB, and these figures come from the physics of dividing power, so they are close to unavoidable. Cheaper or poorly built splitters may lose more, and loss tends to be higher at UHF channels. Long cable runs add more loss.

In practice:

  • Strong signal: a splitter usually works without trouble.
  • Moderate signal: it may work but with some channels dropping to pixelation.
  • Weak signal: splitting may push some channels below what the TV can decode. Consider an amplifier, as covered below.

Choosing a splitter

  • Use the right number of outputs. Pick a 2-way splitter for two TVs, 3-way for three, and so on. A bigger splitter than you need adds unnecessary loss.
  • Check the frequency range. It should cover the TV band (typically 5 to 1000 MHz or higher for modern splitters).
  • Look for good shielding and F-type connectors, which suit most antenna runs.
  • Consider a “balanced” design. Some splitters have lower loss at their outputs.
  • Avoid combining. A splitter used backward as a combiner is a different job, and its use is outside this guide.

Step-by-step

  1. Plan the cable routes from the antenna entry point (or the antenna) to each TV. Shorter runs lose less.
  2. Use RG6 coax and good connectors. See RG6 vs RG59 coax for a TV antenna.
  3. Install the splitter in a dry, accessible place such as near where the cable enters the house. With an outdoor antenna, the grounding block belongs outdoors ahead of the splitter. See how to ground a TV antenna mast and protect it from lightning.
  4. Connect the antenna cable to the splitter’s input port, usually labeled “In”.
  5. Connect each TV to an “Out” port using its own cable.
  6. Terminate unused ports with a 75-ohm terminator cap if the manufacturer recommends it, which can reduce stray signal and noise.
  7. Run a channel scan on each TV, since each tuner works separately.

Adding an amplifier

If the picture is worse after splitting, an amplifier may help. Options:

  • A distribution amplifier placed before the splitter (or a splitter with built-in amplification) makes up for splitter loss.
  • A mast-mounted preamplifier boosts the signal at the antenna before cable loss.

An amplifier does not help every case, and it can overload tuners where the signal is already strong. See how to install a TV antenna amplifier for wiring and tradeoffs.

Powered antennas and power inserters

If your antenna or preamp is powered through the coax by a power inserter, the DC power has to reach the antenna side of the system. The inserter should usually go ahead of the splitter, on the side closer to the TVs and away from the antenna, and the splitter should be placed after it. Some splitters block DC on certain ports, so check the product’s documentation. Follow the amplifier or antenna manual for the order of components.

All TVs share one antenna direction

With a single antenna, every TV gets the same signal. If you use a rotator, rotating changes what every TV receives. Aim for a direction that gets the stations the household watches. For more, see how to aim and align a long-range TV antenna.

Alternatives to splitting

  • A network tuner or DVR that receives the antenna signal and streams it over your home network to TVs, tablets or phones. It reduces cable runs but depends on a good network.
  • One TV connected to the antenna, with a streaming or HDMI distribution setup to share the picture. This has its own cost and limitations.
  • A separate small antenna for a TV in a hard-to-reach room, if signal is strong enough locally.

Troubleshooting

  • A TV has no channels: Check that the cable is tightly connected at each end and rescan.
  • Pixelation after splitting: Try a lower-loss splitter, a shorter cable, or an amplifier. Try a direct connection to one TV to see the baseline signal.
  • One TV works and another does not: Compare cables and connectors, and swap the cable between the two.
  • Interference: Make sure the unused port is terminated and cables are away from electronics; see TV antenna interference from Wi-Fi and how to fix it.

The complete guide to installation and wiring

How to Install an Outdoor TV Antenna
Read the guide

Keep exploring

Guides from other topics

All topics →