What an amplifier does, and when you need one
A TV antenna amplifier (also called a booster or preamp) increases the strength of signals coming from the antenna. It does not create signal from nothing, and it amplifies noise along with the signal. It is most useful in two situations:
- The signal from the antenna is weak because the towers are far away.
- Signal is being lost along a long cable run or by a splitter feeding several TVs.
An amplifier is not a good fix when the signal is already strong. Too much gain can overload the TV’s tuner, which often causes pixelation or missing channels. If your channels already come in cleanly, leave the amplifier out. If you have a choice, try the antenna without an amplifier first, and aim it carefully; see how to aim and align a long-range TV antenna.
Types of amplifiers
- Mast-mounted preamplifier: placed on the mast close to the antenna, powered through the coax by a power inserter indoors. Placing it near the antenna amplifies the signal before cable loss, which is generally the best location for weak signals.
- Distribution amplifier: placed indoors, usually where the cable splits to feed several TVs. It makes up for splitter loss rather than improving the reception from the antenna itself.
- Built-in amplifier: many amplified antennas, including a number of onn models, include an amplifier that is powered through a USB or power adapter. These usually come with their own instructions and can often be switched on or off.
Before you install
- Make sure the amplifier suits your reception band (most cover VHF and UHF).
- Check which parts are included: the amplifier, a power inserter or supply, short jumper cables and mounting hardware.
- Consider your signal strength. A very strong local signal usually needs no amplifier.
- Read the manufacturer’s instructions for your model, since wiring details differ.
Installing a mast-mounted preamp with a power inserter
Always unplug the power inserter while connecting cables, and never power the amplifier with nothing connected to its input if the manual says not to.
- Mount the preamp on the mast or near the antenna, using the supplied clamp. Keep it as close to the antenna terminals as practical.
- Connect the antenna to the amplifier’s input, usually labeled “In” or “Antenna”, using a short length of coax or the connector the kit provides.
- Connect the amplifier’s output to the coax that runs down into the house. Seal outdoor connectors with weatherproofing as directed.
- Run the coax indoors to the power inserter. Connect the cable coming from the antenna to the port on the inserter marked for the antenna or amplifier.
- Connect the inserter’s output to the TV (or splitter), with the other port labeled “TV” or “Out”.
- Plug in the power supply to the inserter and to an outlet.
- Scan for channels on the TV, and compare with what you received before.
If you are also grounding the mast and coax, the grounding block goes outdoors where the cable enters the building, ahead of the power inserter. See how to ground a TV antenna mast and protect it from lightning.
Installing a distribution amplifier
- Place the amplifier near the point where the cable splits, in a dry spot near an outlet.
- Connect the incoming antenna cable to the input.
- Connect each TV cable to an output.
- Plug in the power supply.
- Scan on each TV.
See how to split a TV antenna signal to multiple TVs for splitters and when to use which.
onn amplified antennas
onn is Walmart’s store brand, and its antenna models vary. Some are indoor antennas with a built-in amplifier and a USB power connection, and outdoor ones may use a separate amplifier or power supply. The wiring order above is a general guide, but follow the printed instructions and diagrams for your exact model. If the instructions show the amplifier near the TV, with power through USB, use that.
Testing and troubleshooting
- No channels after installation: Check that the power supply is plugged in, that the cable is on the correct port of the inserter, and that the amplifier’s input and output are not reversed.
- Fewer channels than before: The amplifier may be overloading the tuner. Try bypassing it, or use an attenuator if the kit offers one.
- Pixelation on some channels: Try rescanning, moving the amplifier, and rechecking connectors. See also TV antenna interference from Wi-Fi and how to fix it.
- Intermittent reception: Check connectors for loose or corroded fittings.
Do omnidirectional antennas really work?
Yes, but with limits. Omnidirectional antennas receive from all directions, which is handy when the towers are spread around you, and they generally work well for nearby stations. They typically have less gain than a directional antenna, so they are weaker at long distances. Adding an amplifier can help in some cases but also amplifies noise from all around.
Can you have an antenna and cable at the same time?
Yes. The usual approach is to keep them on separate inputs, or switch between them. Most TVs have a single coax input that can handle either an antenna or cable at one time. To use both, you can connect cable through a set-top box via HDMI and the antenna to the TV’s coax input, or use an A/B switch that you toggle between the two. Combining the two signals in a splitter backward is not recommended, because cable and antenna signals can interfere. If you are connecting a TV to cable, see how to connect an onn TV to cable.