Ham Radio Antennas

Multiband HF Vertical Antennas: DX Commander, GAP Eagle, SE X80 and More

How multiband HF verticals differ, with notes on the DX Commander, SE X80, SE HF-360, GAP Eagle and G8JNJ-style designs, plus ground system and tuner needs.

On this page
  1. Three kinds of multiband vertical
  2. DX Commander
  3. SE X80
  4. SE HF-360 and other radial-free claims
  5. GAP Eagle
  6. G8JNJ broadband vertical
  7. Ground system and tuner expectations
  8. Choosing between them

Multiband HF verticals are popular because they fit in a small garden and work several bands from one support. They are not all built the same way, though, and the differences decide what you need to add: radials, a tuner, a choke, or all three. This page groups the commonly searched models by how they work.

Three kinds of multiband vertical

  • Resonant element verticals. A pole supports separate wire elements, one per band, each cut to a quarter wavelength (or loaded), fed at the base. The DX Commander is the best-known example. Each band is genuinely resonant, so the antenna usually needs no tuner on those bands.
  • End-fed, non-resonant verticals. A single radiator is fed through an impedance transformer at the base and matched with a tuner. The SE X80 style falls here.
  • Trap or loaded verticals. Traps or coils make one tube act as different lengths on different bands. The classic ground-mounted trap verticals work this way.

DX Commander

The DX Commander is a telescopic fibreglass pole carrying a set of wire elements, one for each band, with a base plate and a radial plate. One builder who used a 9 m Classic kit reports good results on 80, 40, 20, 17, 15 and 10 m, with the 40 m element also giving a usable match on 6 m. In that build, the 80 m element works as a loaded quarter-wave, and 10 m works as a three-quarter-wave.

Practical points from that write-up and general experience:

  • The antenna needs guying, and raising it is easier with a helper.
  • Radials do the real work. That builder used 4 m radials in bunches and normally ran four bunches, noting that more radials improve efficiency.
  • Setup was around ten minutes and pack-down a little longer, which suits field days and temporary garden use.
  • Elements interact a little, but the antenna is reported to tolerate imperfect layout.

Check the maker’s current kit options, since the range has several versions with different heights and band coverage.

SE X80

The Sigma Eurocom SE-HF-X80 is sold as an end-fed aluminium vertical for 80 m to 6 m. According to the listing, it is about 6 m tall, uses a 6:1 transformer in a weatherproof box at the base, is rated for 400 W PEP for intermittent amateur use, and needs an ATU (a manual one on some bands, an internal rig tuner on others). It is marketed as not needing a radial or counterpoise set.

Treat “radial-free” with care. Any vertical needs some return path for the currents; with no radials, the coax shield and the ground do that job, which is why choking the coax and choosing the mounting position matter. One reviewer was happy with ground-level mounting, a 25 ft run of coax and FT8 contacts at 50 W. Another found the top section bent in strong gusts, so consider guying, thicker upper tubing or lowering it in storms.

SE HF-360 and other radial-free claims

The SE HF-360 fibreglass vertical is described in at least one buyer’s guide as a roughly six-metre antenna that works without radials. I would verify the exact bands, height and tuner requirements on the seller’s listing and the manual before buying; reviews of this model are thin. The same advice applies to any radial-free vertical: ask what the return path is, then test with an analyzer.

GAP Eagle

GAP’s verticals are commercially built, off-ground designs aimed at users who want a more permanent, tidier installation than a pole-and-wire kit. I could not find usable independent detail on the Eagle model, so check the manufacturer’s data on height, band coverage, counterpoise needs, wind rating and power handling before comparing it with a kit like the DX Commander.

G8JNJ broadband vertical

G8JNJ is an amateur call sign associated with a broadband HF vertical design that is built rather than bought. Homebrew broadband verticals usually trade some efficiency for wide coverage and rely on a transformer or tuner at the base. If you build one, measure it with an antenna analyzer rather than trusting a published curve, and expect results to depend on your radials and nearby objects.

Ground system and tuner expectations

Choosing between them

  • Want to build, tweak and take it to the field: the DX Commander style.
  • Want a simple end-fed pole and already have a tuner: an SE X80 style antenna, mounted clear of buildings and secured against wind.
  • Want a permanent, low-maintenance install: a commercial off-ground vertical, after checking the manufacturer’s specifications.

For the wider picture, see our guide to HF antennas for ham radio. If you mainly listen, the best vertical antenna for listening to HF radio covers different priorities.

The complete guide to ham radio antennas

HF Antennas for Ham Radio: Choosing the Right Type
Read the guide

Keep exploring

Guides from other topics

All topics →