Ham Radio Antennas

How to Build a Homebrew Indoor HF Antenna

Build an indoor HF antenna from wire: attic or bent dipole, room-perimeter loop and random wire options, with tuning, noise and RF safety advice.

On this page
  1. Reality check
  2. Options
  3. Build: a bent indoor dipole
  4. Tuning notes
  5. Noise and RFI
  6. RF exposure and safety
  7. Improving it

An indoor HF antenna is always a compromise: walls, wiring and furniture absorb or distort signals, and household electronics add noise. Even so, many operators make contacts from flats, attics and dorm rooms. This guide covers realistic options and a build you can do with common parts.

Reality check

Expect lower efficiency and higher noise than outdoors. You can still do well on the bands that suit your space, especially with digital modes and CW, but do not expect to compete with a full-size outdoor antenna. If you can put even a small wire outside, see our stealth antenna guide.

Options

  • Attic or loft dipole. If you have an unheated attic with wooden roofing and no metal foil insulation, a dipole run along the ridge or bent to fit often works best.
  • Bent or folded dipole in a room. Run wire around the ceiling line or picture rail, with the ends insulated and kept out of reach.
  • Room-perimeter loop. A loop of wire around the ceiling, fed through a tuner, is a common stealth approach.
  • Random wire plus tuner. A long wire along a wall or out of a window, with a tuner and a counterpoise.
  • Small magnetic loop. Compact and good at rejecting local noise, but narrow band and needing retuning. See magnetic loop antennas.

Build: a bent indoor dipole

This is the simplest option, and the one I would try first.

  1. Pick a band. 20 m is a practical starting point for small spaces; a half-wave is about 10 m (33 ft) in total. Lower bands need more wire, and you can bend ends back on themselves.
  2. Calculate the length. Total length in feet is roughly 468 divided by the frequency in MHz. Cut each leg a little long. See how to calculate dipole length for the method and the trimming approach.
  3. Make the centre. Use a small insulator or plastic box with a 1:1 current balun or choke and an SO-239 or similar connector. Solder the two legs to the connector or balun terminals.
  4. Mount the wire. Run it along the ceiling or ridge on small insulated hooks or tape, as high as you can, away from mains wiring and large metal objects. Bend corners gently.
  5. Add a choke. Put a common mode choke on the coax near the feed point, because indoor antennas often have a lot of common-mode current.
  6. Measure. Check resonance and SWR with an antenna analyzer and trim the wire for the lowest SWR on your chosen part of the band. A tuner can handle the rest. See whether you need an ATU.

Tuning notes

Indoor antennas tune differently from the formula because nearby objects detune them. Expect to trim, and to retune if furniture or wiring changes. A good SWR reading does not prove it radiates well, but a poor one tells you something is wrong.

Noise and RFI

  • Switching power supplies, LED lights and chargers raise the noise floor. Turn them off when you listen and try moving the antenna away from them.
  • RF can also get into household electronics when you transmit. Using lower power and keeping the coax choked helps.

RF exposure and safety

An antenna inside the living space puts you close to the radiating element. Follow the exposure guidelines used in your country, keep power low, keep the antenna away from people and pets, and do not transmit with anyone touching it. Do not run wire near mains cables, and never use gas pipes or plumbing as antennas or grounds.

Improving it

  • Raise the wire higher and move it away from metal.
  • Try a different orientation.
  • If you are mainly listening, try a small loop for better noise rejection.
  • For help picking antenna types, see our HF antenna guide.

The complete guide to ham radio antennas

HF Antennas for Ham Radio: Choosing the Right Type
Read the guide

Keep exploring

Guides from other topics

All topics →