Ham Radio Antennas

How to Build a 2 Meter J-Pole Antenna From Copper Pipe or Ladder Line

Build a 2 meter J-pole antenna from copper pipe or ladder line: how it works, starting dimensions, finding the feed point, tuning with an SWR meter and mounting it.

On this page
  1. How a J-pole works
  2. What you need
  3. Starting dimensions
  4. Build the copper pipe version
  5. Build the ladder line version
  6. Find the feed point and tune
  7. Mounting, weatherproofing and safety

A 2 meter J-pole is a simple, inexpensive vertical antenna you can build from copper pipe or ladder line in an afternoon. It is a half-wave radiator with a quarter-wave matching stub, fed by coax connected at a tap point on the stub. The numbers below are starting points; every build needs trimming and testing.

How a J-pole works

The J-pole’s long section is a half-wavelength radiating element. At its bottom end the impedance is very high, so it is joined to a quarter-wave shorted stub that acts as an impedance transformer. The coax attaches a short distance above the shorted end of the stub, where the impedance is close to 50 ohms. The antenna is end-fed and needs no radials, though the coax shield should be kept from radiating, which a common mode choke helps with.

What you need

For a copper pipe version:

  • copper pipe (commonly 1/2 inch), tee or elbow fittings and an end cap, plus a short connecting piece;
  • a coax connector or pigtail and a way to clamp or solder it to the pipe;
  • pipe clamps or hose clamps for the feed tap;
  • a mounting mast and weatherproofing material.

For a ladder line version:

  • 450 ohm window line or ladder line;
  • a coax connector or short pigtail of coax;
  • a means of hanging it, such as a short non-metal support and rope.

You also need a hacksaw, a soldering setup or suitable fittings, and an SWR meter or antenna analyzer.

Starting dimensions

Frequencies on 2 m centre near 146 MHz. Formulas:

  • Half wave in free space: 468 divided by the frequency in MHz, in feet. At 146 MHz this is about 3.2 ft (about 38.5 in).
  • Quarter wave in free space: 234 divided by the frequency in MHz, in feet, which is about 1.6 ft (about 19 in).

Real J-poles differ from these formulas because of pipe thickness, fittings and velocity factor. The overall length of the total structure is about three-quarters of a wavelength; published copper-pipe plans commonly come out at a little under 5 ft overall, and ladder-line versions often come out slightly shorter because of the line’s velocity factor. Treat a published plan as a starting point, cut things a little long, and trim.

Build the copper pipe version

  1. Cut the long section (the radiator) and the short section (the stub) from pipe, following a trusted plan for your pipe diameter.
  2. Join them at the bottom with a tee or elbow, and a short shorting piece, so the stub’s end is electrically shorted to the radiator at the base.
  3. Cap the top of the radiator and, if you like, drill a small drain hole so condensation can escape.
  4. Attach the feed. Clamp or solder the coax centre conductor to the radiator and the shield to the stub at the feed point, a few inches above the shorted base. Make the connection movable at first so you can adjust it.
  5. Seal and test before final assembly.

Build the ladder line version

  1. Cut a length of ladder line for the stub and radiator following a plan.
  2. At the bottom, short the two conductors together.
  3. At the top of the stub section, cut one conductor so that the other extends as the radiating section.
  4. Make the feed connections near the bottom, again adjustable at first.
  5. Hang it from a non-metallic support, away from metal.

Find the feed point and tune

  1. Connect the coax with the feed point a few inches above the shorted end.
  2. Measure SWR at 146 MHz or your desired frequency, or sweep with an analyzer.
  3. Move the feed point up or down along the stub in small steps, rechecking each time, until SWR is lowest.
  4. If the lowest SWR is at the wrong frequency, adjust the length of the whole antenna by trimming the top.
  5. Aim for an SWR well under 2:1. See what a good SWR is.

Mounting, weatherproofing and safety

  • Mount the antenna as high and clear of metal as you can. Mount to a non-metallic mast or standoff if the structure is metal.
  • Seal the connections against rain.
  • Keep it well away from power lines and do not install it where a fall could contact them.
  • Keep people away from the antenna while transmitting.

Installing it outdoors follows the same principles as any VHF/UHF antenna; see how to install a UHF radio antenna and VHF/UHF mobile and marine antennas. For HF projects, see our HF antenna guide.

The complete guide to ham radio antennas

HF Antennas for Ham Radio: Choosing the Right Type
Read the guide

Keep exploring

Guides from other topics

All topics →