Ham Radio Antennas

HF Delta Loops and Broadband Folded Dipoles

How delta loop antennas and broadband folded dipoles (T2FD and the Yaesu YA-30 style) work on HF, their sizes, matching needs and the trade-offs of each.

On this page
  1. Delta loops
  2. Broadband folded dipoles
  3. Which one to choose

Two wire designs often come up for people who want something better than a simple dipole: the delta loop, valued for low noise and decent performance, and the broadband folded dipole, valued for covering a huge range of frequencies with little or no tuner. Both need space, and both have trade-offs worth understanding.

Delta loops

A delta loop is a full-wave loop of wire formed into a triangle, usually with one corner pointing up and the base horizontal near the ground, or the reverse. Its total wire length is roughly 1005 divided by the frequency in MHz, in feet. For 40 m, that is about 140 ft of wire, which fits into a triangle with sides of around 47 ft.

Why people use them

  • Closed loops tend to pick up less static-type noise than open dipoles or verticals, which helps on the lower bands.
  • A full-wave loop can give a little gain over a dipole and a useful pattern from a modest height.
  • The loop is a single wire with no end that needs to be insulated from the ground, so it is easy to support from a mast or tree.

Feed point and polarisation

Where you feed the loop affects polarisation. Feeding at the bottom corner of a delta tends to give mostly horizontal polarisation; feeding in the middle of a vertical side gives vertical polarisation. Feeding at a lower point on a side is a compromise that suits low-angle DX. Pick the feed point that matches your support layout.

Matching and multiband use

A full-wave loop has an impedance around 100 ohms, so it is often matched with a quarter-wave section of 75 ohm coax or a suitable balun, then fed with 50 ohm coax. A loop cut for 40 m can also work on 15 m with a tuner or open-wire line, but its pattern changes on harmonics. If you want true multiband use, use an ATU and consider ladder line, and measure the results with an antenna analyzer.

Limitations

  • It needs space and at least two or three supports.
  • It is physically larger than a dipole for the same band.
  • Close proximity to buildings and trees changes the resonance.

Broadband folded dipoles

A broadband folded dipole uses a loop of wire, usually with a termination resistor, to flatten the antenna’s impedance across a very wide range. Variants are called T2FD (tilted terminated folded dipole) or BBTD (broadband terminated dipole). They are fed through a high-ratio balun, with designs commonly using ratios such as 9:1, 12:1 or 16:1 and termination resistors in the 500 to 1250 ohm range.

The Yaesu YA-30 as an example

The commercial Yaesu YA-30 is a multi-wire folded dipole for 1.6 to 30 MHz with a 50 ohm input. According to its DX Engineering listing, it is about 83 ft long, is rated at 150 W PEP voice, and needs no tuner, with SWR better than 2:1 up to 18 MHz and better than 3:1 above that. Its two-wire construction keeps wind loading lower than you might expect.

The trade-off

Broad coverage costs efficiency. The termination resistor absorbs some of the power, so a resonant dipole on a specific band can outperform a broadband one. Palomar Engineers makes this point itself while noting that simplicity is the attraction for general coverage and shortwave listening. Low power ratings on commercial models also matter.

If you want the fundamentals of how a folded dipole differs from a plain one, see the difference between a dipole and a folded dipole, the benefits of folded dipoles and their disadvantages.

Which one to choose

  • Delta loop: best if you have the space, want a quiet antenna and are willing to build.
  • Broadband folded dipole: best if you want to hop around bands without a tuner, accept some loss, and have a long straight run for the wire.
  • Neither: if you only operate on one or two bands, a simple dipole is often more efficient and cheaper.

See the HF antenna guide for how these compare with verticals and end-feds.

The complete guide to ham radio antennas

HF Antennas for Ham Radio: Choosing the Right Type
Read the guide

Keep exploring

Guides from other topics

All topics →